Company Name:
Omni Manufacturing Inc.
Omni Manufacturing Inc.
Company Address:
901 McKinley Road
St. Marys, OH 45885
901 McKinley Road
St. Marys, OH 45885
Date Job is Available:
March 20th, 2024
March 20th, 2024
Deadline for Application:
April 12th, 2024
April 12th, 2024
Job Description:
| QUALITY | ||||||
| FOLLOWS QUALITY SYSTEM CONTROLS (ISO/QS9000) | ||||||
| IS ABLE TO PASS, FAIL, STOP PRODUCTION OR HOLD SHIPMENT FOR PRODUCT | ||||||
| NON-CONFORMANCE | ||||||
| CAN PERFORM INSPECTION PROCESS - BLUE BOOK AND APPLICABLE FORMS INCLUDED | ||||||
| FOLLOWS IPII DOCUMENTATION/IPII & TRAVELER WORK INSTRUCTIONS | ||||||
| IDENTIFY FIRST PIECE/LAST PIECE/MASTER SAMPLE | ||||||
| OPERATE APPROPRIATE GAGES, CALIPERS, MICROMETERS, PROTRACTORS, ETC. | ||||||
| FOLLOWS MEASUREMENT METHODS SYSTEM | ||||||
| FOLLOWS SCRAPING PROCESS | ||||||
| VISUALLY INSPECT PARTS FOR DEFECTS | ||||||
| HAS KNOWLEDGE OF THE FOLLOWING DOCUMENTS: | ||||||
| CONTROLLED LOT TAG | ||||||
| CUSTOMER SPECIAL CHARATERISTICS | ||||||
| DEVIATIONS | ||||||
| ACCURATELY COMPLETE QUALITY REPORTS | ||||||
| JOB DESCRIPTION | ||||||
| DO NOT OPERATE UNLESS YOU HAVE BEEN AUTHORIZED | ||||||
| NO OPERATOR IS AUTHORIZED TO TRAIN OTHER EMPLOYEES | ||||||
| RECOGNIZE AND IDENTIFY THE FOUR (4) E-STOP LOCATIONS | ||||||
| OPERATOR MUST PERFORM A LIGHT CURTAIN CHECK BEFORE THE START OF THE SHIFT | ||||||
| ALL GAS CYLINDERS ARE TO BE CHAINED IN THE STORAGE RACKS | ||||||
| NO GAS CYLINDER IS TO BE MOVED UNLESS THE CAP IS SECURED | ||||||
| EMPTY WELDING WIRE IS TO BE CHANGED BY AUTHORIZED PERSONNEL ONLY | ||||||
| MAINTAIN GOOD HOUSEKEEPING AROUND THE WELDING CELL | ||||||
| MAKE SURE FIXTURES ARE CLEAN OF WELD SPATTER & THAT THEY WORK PROPERLY | ||||||
| INSPECT FOR ANY WEAR THAT MAY MISLOCATE PART | ||||||
| MAKE SURE LOCATOR FOR TAB IS NOT DAMAGED OR WORN | ||||||
| MAKE SURE CLAMPS SEAT PROPERLY WITH SAME AMOUNT OF PRESSURE, ARE | ||||||
| CENTERED AND NOT OVERLY TIGHT AND BASE CLEAN | ||||||
| AT NO TIME AFTER ROBOT BEGINS ITS CYCLE IS ANY PERSONNEL TO ENTER THE | ||||||
| WELDING CELL (STATION) | ||||||
| OPERATOR MADE AWARE OF POTENTIAL OF FLASH BURN | ||||||
| ANYTIME PERSONNEL ENTERS THE ROBOTIC WELDING CELL, LOCK OUT/TAG OUT | ||||||
| PROCEDURES MUST BE IMPLEMENTED AND FOLLOWED…NO EXCEPTIONS | ||||||
| ONLY AUTHORIZED LOCK OUT/TAG OUT EMPLOYEES ARE AUTHORIZED TO ENTER THE | ||||||
| WELDING CELL (STATION) | ||||||
| OPERATOR KNOWLEDGEABLE ABOUT THE OPERATION OF THE E-STOP AND LOCK | ||||||
| E-STOP AT THE GATE | ||||||
| READ AND UNDERSTAND BLUEPRINTS | ||||||
| PRODUCE A WELDED PART WHICH TESTS IN ACCORDANCE WITH PRINT AND/OR | ||||||
| PROCESS SHEETS | ||||||
| PERFORM BASIC MATH SKILLS | ||||||
| CORRECTLY OPERATE MEASURING DEVICES | ||||||
| MAINTAIN HOUSEKEEPING IN HIS/HER WORK AREA | ||||||
| STAND FOR AN ENTIRE SHIFT | ||||||
| REMAIN ALERT FOR AN ENTIRE SHIFT | ||||||
| HAVE GOOD FINGER AND HAND DEXTERITY | ||||||
| PERFORM REPETITIVE TASKS | ||||||
| ADJUST AIR PRESSURES | ||||||
| ADJUST HEAT TEMPERATURES | ||||||
| ADJUST TIP CLEARANCES | ||||||
| ADHERE TO ALL OMNI POLICIES, PROCEDURES & INSTRUCTIONS | ||||||
| MAINTAIN ATTENDANCE | ||||||
| POSESS KNOWLEDGE OF A MANUFACTURING ENVIRONMENT | ||||||
| WORK IN EXTREME TEMPERATURES | ||||||
| PERFORM MINOR PROGRAMMING OF THE ROBOT'S COMPUTER | ||||||
| POSSESS STRONG WELDING BACKGROUND | ||||||
| OPERATE MOTOMAN ROBOITC WELDER | ||||||
| OPERATE STS WELDER | ||||||
| OPERATE A FORKLIFT | ||||||
| WORK IN A GREASY OR DIRTY ENVIRONMENT | ||||||
| WORK IN A LOUD ENVIRONMENT | ||||||
| UNDERSTAND HOW TO USE BARCODE SYSTEM/TERMINAL OPERATION | ||||||
Qualifications:
Minimum of 1 year of experience with ABB welding cells. Tig welding a PLUS! All shifts available.
Minimum of 1 year of experience with ABB welding cells. Tig welding a PLUS! All shifts available.
How to Apply
Contact Name: Danielle Lunz
Website: omnimfg.com/careers